Product

Force and Torque

PRO-1N_thumb
• JISC produces extremely low capacity spring tester that conform to highest Grade 05 of JIS B 7738.
• This tester is meant only for compression spring to cater for Medical Industries, High End Branded Ball Pen Industries, Pogo Pin, Fax Scanner Machine Industries & etc.
1-force-and-torque_thumb
• The whole series meets 05 grade (Highest Grade) of JIS B 7738 Coil Spring Compression / Tension Tester.
• In addition to 1 -Step , 2 -Step, 3 -Step Automatic Tests, Free Length, Initial Tension, Solid Length, Peak Load can be measure.
• Unit select able among N, gf, kgf, lbf and inch covered by English version.
1-1-2-pro-twin-column_thumb
• The whole series meets 05 grade (Highest Grade) of JIS B 7738” Coil spring Compression / Tension Tester
• In addition to 1 -Step , 2 -Step, 3 -Step Automatic Tests, Free Length, Initial Tension, Solid Length, Peak Load can be measured
• Unit select able among N, gf, kgf, lbf and inch covered by English version
job-ct-_thumb
• High Performance Amplifier, Servo Motor, Ball Screw with LM Guide to maintain high accuracy.
• Models number can stored with specifications input for judgement purposes. Able to check 1, 2, 3 Step Load, Spring Rate, Free length, Initial Tension (Tension Spring) and Solid Height (Compression Spring).
• Tolerance input by +/- value or %. Auto switch over for power supply of AC 110 to 240V. Can link up to computer using our MXR-01 & BQC-01 QC Monitor Software
ace_thumb
• ACE series Fully Automatic Spring Tester withSorting function.
• This tester conform to JIS B 7738 Grade 0.5 which is the highest grade.
• It function is similar to our PRO Series of spring tester except that its touch screen with SPC control function to show Histogram & Trend Chart.
• There are only 2 models for this series, ACE-100N & ACE 1kN only.
SST_thumb
• Compression and Side Force Spring Tester is a new and innovative machine that is develop from our spring testing machine over the years.
• There will be three load cells above and under the compression and an additional three load cells for the XY axis, using 9 load cells for total compressive load on proprietary software, to obtain displacement force from the top and bottom moment of the spring with reference to the center.
• All data can be collected in a single using this Compression and Side Force Spring Tester
<413393F182C290DC82E85F97A0288A4F91A4292D897095B6205B5546545D2D8
• Deliver High Precision Measurement via 3 load cells even if there is unbalance load.
• The tester alone can meet a variety of specifications such as JIS K6400-2, JASO B408 & etc.
• This UFT series can satisfy a variety of urethane foam test.
• The 3 load cells enable this tester to deliver high precision load detection even in the presence of unbalance load
NST-500Nm_thumb
• This machine is for measuring the tightening force of bolts in accordance to JIS B 1084 testing requirements.
• Tightening Clamping Force (F), Tightening Torque (T), Thread Torque (Tth), Tightening Rotation Angle and Extension can be measured.
• Testing speed of 30RPM can also be set as per ISO 16047 requirements.
tex_thumb
• So far texture of foods is judge by human sense of mouth feel.
• The human sense is very important criteria but is has big problem.
• Definition is not clear and feeling differs from person to person. Texture Tester TEX-100 can visualize the fuzzy mouth feel with “numeric value” so that you can make objective judgment of the texture.
• For example, if you are manufacturer or server of the foods for children and elderly people, it is very important to check safety hardness for swallowing of such foods.
pro-t_thumb
• Manual or automatic test can be chosen.
• Numbers are shown in display as digital scale is attached to XY table and rotating table.
• Measurement of torque and load, as well as angle based on torque or load input are done easily. (PRO-TS Type)
• Passing range and Good 1 Poor results are shown in bar graphics. Visual judgement and management is possible.
Page 1 of 3123